Seting Smartfren AC682 di Ubuntu 12.04

Assalamu’alaikum Wr.Wb

Setelah install Pangolin saya langsung seting modem ini, karena linux sepenuhnya tak bisa jauh dengan internet. Ada sedikit perbedaan sedikit dari seting di Oneiric. Silahkan ikuti setiap petunjuknya sebagai berikut :

Pastikan sudah install wvdial (download di sini)

Colokkan modem

Buka terminal (ketik di terminal yang cetak miring)

lsusb

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 04f2:b044 Chicony Electronics Co., Ltd Acer CrystalEye Webcam
Bus 004 Device 003: ID 1c4f:0003 SiGma Micro HID controller
Bus 005 Device 007: ID 19d2:ffdd ZTE WCDMA Technologies MSM

Tidak perlu di eject, karena sudah ter eject otomatis

sudo modprobe usbserial vendor=0x19d2 product=0xffdd

masukkan password dan tunggu sesaat.

dmesg | tail

[ 1416.413197] usbserial_generic 5-1:1.0: generic converter detected
[ 1416.413389] usb 5-1: generic converter now attached to ttyUSB0
[ 1416.415167] usbserial_generic 5-1:1.1: generic converter detected
[ 1416.415294] usb 5-1: generic converter now attached to ttyUSB1
[ 1416.417176] usbserial_generic 5-1:1.2: generic converter detected
[ 1416.417346] usb 5-1: generic converter now attached to ttyUSB2
[ 1416.419331] scsi9 : usb-storage 5-1:1.3
[ 1417.420144] scsi 9:0:0:0: Direct-Access     EVDO     ReV A            7.00 PQ: 0 ANSI: 0 CCS
[ 1417.420881] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 1417.509137] sd 9:0:0:0: [sdb] Attached SCSI removable disk

sudo wvdialconf

Editing `/etc/wvdial.conf’.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0   S1   S2   S3   S4   S5   S6   S7
Modem Port Scan<*1>: S8   S9   S10  S11  S12  S13  S14  S15
Modem Port Scan<*1>: S16  S17  S18  S19  S20  S21  S22  S23
Modem Port Scan<*1>: S24  S25  S26  S27  S28  S29  S30  S31
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 — failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 — ~�}#�!}!}!} }3}”}&} } } } }#}%�#}%}’}”}(}”W}0~
ttyUSB0<*1>: failed with 9600 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 — and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 — failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 — failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 — and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 — OK
ttyUSB2<*1>: ATQ0 V1 E1 Z — OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 — OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 — OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttyUSB2<*1>: Modem Identifier: ATI — Manufacturer: +GMI: China TeleCom
ttyUSB2<*1>: Speed 9600: AT — OK
ttyUSB2<*1>: Max speed is 9600; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK

Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB2<Info>: Speed 9600; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0”

sudo gedit /etc/wvdial.conf

isi jendela yang muncul dengan baris berikut :

[Dialer smart]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1
Modem Type = Analog Modem
Command Line = ATDT
ISDN = 0
New PPPD = yes
Phone = #777
Modem = /dev/ttyUSB0
Username = smart
Password = smart
Baud = 460800

kemudian Save

kemudian jalankan dengan perintah

sudo wvdial smart

jika muncul seperti ini, maka modem siap digunakan.

–> WvDial: Internet dialer version 1.61
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
OK
–> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
–> Modem initialized.
–> Sending: ATDT#777
–> Waiting for carrier.
ATDT#777
CONNECT 3100000
–> Carrier detected.  Starting PPP immediately.
–> Starting pppd at Fri May  4 12:29:25 2012
–> Pid of pppd: 3468
–> Using interface ppp0
–> pppd: ���[08]@|�[08]
–> pppd: ���[08]@|�[08]
–> pppd: ���[08]@|�[08]
–> pppd: ���[08]@|�[08]
–> local  IP address 10.253.59.155
–> pppd: ���[08]@|�[08]
–> remote IP address 10.20.31.17
–> pppd: ���[08]@|�[08]
–> primary   DNS address 10.17.3.252
–> pppd: ���[08]@|�[08]
–> secondary DNS address 10.17.3.246
–> pppd: ���[08]@|�[08]

Semoga membantu sedikit coretan dari saya, jika bingung silahkan tanya di komentar.

Dan yang mau pulsa gratis alangkah baiknya klik DI SINI gan!!!!

Wassalamu’alaikum Wr.Wb

13 thoughts on “Seting Smartfren AC682 di Ubuntu 12.04

  1. gan di Precise saya kok tulisannya “PPP daemon has died (exit code = 2)”, sedangkan kalo saya connect-in via “sudo pppd call smart” via pppconfig berjalan dengan lancar, tapi masalahnya kalo pake pppconfig saya gatau cara disconnect-in nya

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s